WalkInReady

Learn the Material

The whole pool in publication order, answers marked. Nothing here is scored and nothing changes your study statistics.

Notice: You have access to 47 of 222 questions in this course. You can subscribe later for only $10/mo. to unlock the entire course.

S1 — Diving Physics: Pressure, Gas Laws, Buoyancy, Light and Sound

33 questions · 7 on the exam · 26 held back

Practice

33 questions

S1001

In seawater, the water pressure alone at a depth of 33 feet is equal to:

  1. AOne atmosphere
  2. BTwo atmospheres
  3. CHalf an atmosphere
  4. DThree atmospheres
Why

Every 33 feet of seawater adds the weight of one atmosphere of pressure.

S1002

What is the absolute pressure on a diver at 33 feet of seawater?

  1. AOne atmosphere
  2. BTwo atmospheres
  3. CThree atmospheres
  4. DOne and a half atmospheres
Why

Absolute pressure adds the one atmosphere of air above the water to the one atmosphere of water.

S1003

What is the absolute pressure at a depth of 66 feet of seawater?

  1. A2 ata
  2. B4 ata
  3. C3 ata
  4. D6 ata
Why

Surface pressure (1 ata) plus 2 atmospheres of water (66 feet) gives 3 ata.

S1004

One standard atmosphere of pressure is equal to about:

  1. A33 psi
  2. B29.4 psi
  3. C7.4 psi
  4. D14.7 psi
Why

Standard atmospheric pressure at sea level is 14.7 pounds per square inch, or 1 ata.

S1005

Absolute pressure is:

  1. AGauge pressure plus atmospheric pressure
  2. BGauge pressure minus atmospheric pressure
  3. CThe water pressure alone at a given depth
  4. DThe pressure shown on a cylinder gauge
Why

Absolute pressure is the total pressure: what the gauge reads plus the atmosphere.

S1006

Boyle's law states that, at a constant temperature, the absolute pressure and the volume of a gas are:

  1. ADirectly proportional
  2. BInversely proportional
  3. CUnrelated to each other
  4. DEqual to each other
Why

When pressure goes up, volume goes down in proportion, and the reverse.

S1007

What happens to the volume of a flexible air space as a diver ascends?

  1. AIt decreases as the pressure is reduced
  2. BIt stays the same at every depth
  3. CIt increases as the pressure is reduced
  4. DIt increases only in warm water
Why

By Boyle's law, less pressure on ascent lets the gas expand.

26 more questions in this group are in the full course.

Unlock the Full Question Bank

Start a 2-day free trial to study every question and take full practice tests. Then $10/month for this course. Cancel anytime in your account. One free trial per person.

S2 — Diving Physiology and Diving Disorders

38 questions · 9 on the exam · 30 held back

Practice

38 questions

S2001

Barotrauma that happens during descent is called a squeeze. Barotrauma during ascent is called:

  1. ANitrogen narcosis
  2. BReverse squeeze
  3. CDecompression sickness
  4. DCaloric vertigo
Why

Pressure injury on the way down is squeeze; on the way up, when trapped gas expands, it is reverse squeeze.

S2002

Which is the most common type of barotrauma in divers?

  1. ATooth squeeze
  2. BLung squeeze
  3. CMiddle ear squeeze
  4. DSinus squeeze
Why

The middle ear is squeezed more often than any other air space.

S2003

A diver feels sharp ear pain during descent. What usually brings immediate relief?

  1. ADescend faster to get past the pain
  2. BHold the breath and continue down
  3. CRemove the mask and continue down
  4. DStop the descent and ascend a few feet
Why

Stopping and rising a little reduces the pressure difference so the ear can be equalized.

S2004

Which methods let many divers clear (equalize) their ears without forcing air?

  1. AYawning, swallowing, or moving the jaw
  2. BHolding the breath and bearing down
  3. CBlowing hard against a pinched nose
  4. DTilting the head fully back
Why

Gentle movements of the jaw and throat open the eustachian tubes for many divers.

S2005

What is the Valsalva maneuver?

  1. ASwallowing hard while pushing the lower jaw forward
  2. BGently exhaling against a pinched nose and closed mouth
  3. CExhaling through the nose into the mask to clear it
  4. DTaking two quick, deep breaths just before descent
Why

The Valsalva maneuver forces gas gently into the middle ear to equalize it.

S2006

When should a diver equalize the ears during descent?

  1. AOnly after pain is felt
  2. BOnly once, on reaching the bottom
  3. CEarly and often, staying ahead of the pressure
  4. DOnly when the descent is complete
Why

Frequent early equalizing prevents the eustachian tube from collapsing under a large pressure difference.

S2007

A person cannot clear his or her ears at the surface before a dive. What should the person do?

  1. ADive and clear forcefully at depth
  2. BDescend head-first to help the ears
  3. CWear ear plugs during the dive
  4. DNot dive
Why

A blocked eustachian tube makes middle ear squeeze much more likely.

S2008

Why must a diver never do a forceful Valsalva maneuver during descent?

  1. AIt can cause alternobaric vertigo or inner ear barotrauma
  2. BIt can make the diver too buoyant and start an ascent
  3. CIt uses up the air supply much faster than normal
  4. DIt can bring on nitrogen narcosis at a shallow depth
Why

Forceful pressure changes can damage the inner ear membranes.

30 more questions in this group are in the full course.

Unlock the Full Question Bank

Start a 2-day free trial to study every question and take full practice tests. Then $10/month for this course. Cancel anytime in your account. One free trial per person.

S3 — SCUBA Equipment

35 questions · 8 on the exam · 28 held back

Practice

35 questions

S3001

What does the first stage of a SCUBA regulator do?

  1. ADelivers air to the diver only when the diver inhales
  2. BMeasures how much air is left in the cylinder
  3. CVents exhaled air into the water
  4. DReduces high cylinder pressure to an intermediate pressure above ambient
Why

The first stage, mounted on the cylinder valve, drops cylinder pressure to a set level over ambient pressure.

S3002

What makes the second stage of a demand regulator open and deliver air?

  1. AInhaling lowers the pressure inside, so water pressure opens the valve
  2. BA built-in timer opens the valve every few seconds
  3. CThe diver presses the purge button for every breath
  4. DThe first stage pushes air through it without stopping
Why

Inhaling lowers the pressure in the second stage; ambient water pressure moves the diaphragm and opens the valve.

S3003

Where does a diver’s exhaled air go in an open-circuit SCUBA regulator?

  1. ABack into the cylinder through the first stage
  2. BThrough at least one check valve into the water
  3. CInto the buoyancy compensator to add some lift
  4. DInto the octopus second stage for the buddy
Why

Open-circuit SCUBA vents every exhaled breath to the water.

S3004

What is the purge button on a second stage used for?

  1. ATo inflate the buoyancy compensator
  2. BTo shut off the air supply at depth
  3. CTo force out water that has entered the regulator
  4. DTo check the cylinder pressure
Why

Pressing the purge button opens the valve manually and blows water out of the second stage.

S3005

What is an octopus?

  1. AA second cylinder with its own separate first stage
  2. BA short hose that joins two cylinders together
  3. CA gauge console with a depth and pressure gauge
  4. DA spare second stage on the diver’s own first stage
Why

An octopus is a spare second stage used if the primary fails or to give air to a buddy.

S3006

Where should the octopus be secured?

  1. AOn or near the chest, where it is easy to reach
  2. BBehind the cylinder, where it stays out of the way
  3. CHanging loose below the diver on a long hose
  4. DInside a BC pocket that zips completely shut
Why

A chest position makes the octopus easy to reach in an emergency.

S3007

How can a diver check before the dive that the octopus works?

  1. APress its purge button once underwater
  2. BBreathe from it during the predive inspection
  3. CLook at the submersible pressure gauge
  4. DBlow into it with the cylinder valve closed
Why

Breathing from the octopus before the dive confirms that it delivers air.

28 more questions in this group are in the full course.

Unlock the Full Question Bank

Start a 2-day free trial to study every question and take full practice tests. Then $10/month for this course. Cancel anytime in your account. One free trial per person.

S4 — Dive Planning and Procedures

38 questions · 9 on the exam · 30 held back

Practice

38 questions

S4001

What does the U.S. Navy call the single greatest safety practice in SCUBA operations?

  1. AWearing a dive computer
  2. BCarrying a knife
  3. CThe buddy system
  4. DUsing a surface float
Why

Buddies are jointly responsible for the task and for each other’s safety.

S4002

One diver in a buddy pair decides to end the dive. What should the other diver do?

  1. AContinue the dive alone
  2. BWait at the bottom for the partner to return
  3. CJoin another buddy pair
  4. DSurface with the partner
Why

If one member of a buddy team aborts a dive for any reason, both divers surface.

S4003

Why must buddies stay close together throughout a dive?

  1. ASo each can give immediate assistance in an emergency
  2. BSo they can share one air supply
  3. CSo they use the same amount of air
  4. DSo their computers show the same depth
Why

The buddy system is based on mutual assistance.

S4004

Buddies become separated during a dive. Under NOAA diving standards, what should each diver do?

  1. AKeep searching at depth until the air supply runs low
  2. BSearch for no more than one minute, then make a controlled ascent
  3. CContinue the dive plan and meet the buddy at the boat
  4. DGo to the bottom and wait there for the buddy to return
Why

A short search, then a controlled ascent to reunite at the surface, prevents two divers from being lost.

S4005

Under NOAA diving standards, what is the maximum ascent rate?

  1. A60 feet per minute
  2. B100 feet per minute
  3. C30 feet per minute
  4. D10 feet per minute
Why

The Navy and Department of the Interior manuals give the same 30 feet per minute limit.

S4006

NOAA recommends a precautionary safety stop on no-decompression dives deeper than 30 feet. Where and for how long?

  1. ABetween 30 and 40 feet for 1 minute
  2. BAt the surface for 10 minutes
  3. CBetween 5 and 10 feet for 20 minutes
  4. DBetween 15 and 20 feet for 3 to 5 minutes
Why

A safety stop is an extra, precautionary step on ascent.

S4007

A diver has an emergency during ascent. What should the diver do about the safety stop?

  1. AOmit it and get safely to the surface
  2. BAlways complete it first
  3. CDouble its length
  4. DDo it on the bottom instead
Why

Safety stops are precautionary; in an emergency getting safely to the surface comes first.

S4008

Two buddies have different dive computers showing different no-decompression times. Which dive profile should the pair follow?

  1. AThe profile of the diver with more experience
  2. BThe most conservative profile
  3. CThe profile of the newer computer
  4. DThe average of the two computers
Why

Both divers in the pair follow the most conservative profile.

30 more questions in this group are in the full course.

Unlock the Full Question Bank

Start a 2-day free trial to study every question and take full practice tests. Then $10/month for this course. Cancel anytime in your account. One free trial per person.

S5 — Emergencies and Rescue

37 questions · 8 on the exam · 29 held back

Practice

37 questions

S5001

A diver has a problem underwater. What should the diver do first?

  1. ARelax, avoid panic, and think through the possible solutions
  2. BSwim to the surface as fast as possible
  3. CDrop all equipment at once
  4. DHold the breath until the problem is solved
Why

Calm thinking, then telling the buddy or surface, gives the best chance of solving the problem.

S5002

A diver is caught (fouled) in fishing line. What is the first and most important action?

  1. AKick hard to break free
  2. BStop and think
  3. CDitch the SCUBA unit at once
  4. DMake an emergency ascent
Why

Panic and overexertion are the greatest dangers to a trapped diver.

S5003

For a trapped diver, what are the greatest dangers?

  1. ACold water and poor visibility
  2. BNitrogen narcosis and noise
  3. CPanic and overexertion
  4. DCurrents and waves
Why

Struggling wastes air and can tangle the diver further.

S5004

A diver suddenly cannot get air. Which is one of the first things to check?

  1. AThat the weight belt is tight
  2. BThat the mask strap is in place
  3. CThat the fins are on correctly
  4. DThat the cylinder valve is fully open
Why

A partly closed valve can cut off air, especially at depth.

S5005

A diver’s primary regulator fails underwater. What should the diver do?

  1. ASwitch to the secondary regulator or alternate air source
  2. BHold the breath and continue the dive as planned
  3. CRemove the mask to find the problem more easily
  4. DInflate the BC fully and stay at the same depth
Why

A redundant second stage or independent air source is the first backup.

S5006

After a loss of air, once the diver is breathing again from a backup source, what should happen to the dive?

  1. AThe dive continues as planned
  2. BThe dive is aborted
  3. CThe diver goes deeper to save air
  4. DThe pair splits up
Why

Any loss of air ends the dive; buddy breathing or a free ascent are used if needed.

S5007

During an out-of-air ascent, why should a diver not ditch the SCUBA unit unless absolutely necessary?

  1. AThe unit keeps the diver warm during the rest of the ascent
  2. BThe unit is needed for buoyancy once the diver is on the surface
  3. CMore air may become available as the surrounding pressure drops
  4. DKeeping the unit on helps prevent narcosis during the ascent
Why

As the diver rises, the lower ambient pressure may let a little more air be drawn from the cylinder.

S5008

What is the preferred way to share air with an out-of-air buddy?

  1. APass one mouthpiece back and forth between them
  2. BMake a free ascent together without sharing air
  3. CHand the buddy the whole cylinder and regulator
  4. DGive the buddy an octopus (alternate second stage)
Why

With an octopus, both divers breathe continuously.

29 more questions in this group are in the full course.

Unlock the Full Question Bank

Start a 2-day free trial to study every question and take full practice tests. Then $10/month for this course. Cancel anytime in your account. One free trial per person.

S6 — The Underwater Environment and Its Hazards

41 questions · 9 on the exam · 32 held back

Practice

41 questions

S6001

What is a rip current?

  1. AA slow current running along the beach
  2. BA powerful, narrow channel of fast-moving water
  3. CA wave that breaks far from shore
  4. DA layer of cold water at depth
Why

Rip currents flow away from shore and occur along U.S. ocean coasts and the Great Lakes.

S6002

How fast can a rip current move?

  1. ANo faster than a person walking slowly along the beach
  2. BAbout one foot per minute, slower than a drifting boat
  3. CUp to about eight feet per second, faster than an Olympic swimmer
  4. DOnly as fast as the tide that is coming in at the time
Why

No swimmer can outswim a strong rip straight back to shore.

S6003

Why do swimmers caught in rip currents often drown?

  1. AThe current pulls them straight down under the water
  2. BThey swim parallel to the shore and become lost
  3. CThey float calmly and wait too long for help
  4. DThey swim straight back to shore against it and tire out
Why

Fighting the current leads to fatigue.

S6004

A diver on the surface is caught in a rip current. What should the diver do?

  1. ASwim parallel to the shore, then back to land at an angle
  2. BSwim straight toward shore as hard as possible
  3. CDive to the bottom and crawl to shore
  4. DRemove all equipment and swim against it
Why

Rip currents are narrow; swimming across them gets you out of the flow.

S6005

Why does swimming parallel to the shore usually get a swimmer out of a rip current?

  1. ARip currents always turn parallel to shore
  2. BMost rip currents are less than 80 feet wide
  3. CRip currents stop after one minute
  4. DRip currents are weakest in the middle
Why

A short swim across the narrow current reaches water that is not flowing out.

S6006

Where do rip currents often form?

  1. AOnly far offshore, in water deeper than 100 feet
  2. BOnly at the mouths of large rivers and streams
  3. CAt low spots or breaks in sandbars, and near jetties and piers
  4. DOnly during storms, far away from any structures
Why

Rips form where water returning to sea can channel through a gap or along a structure.

S6007

How is a rip tide different from a rip current?

  1. AThey are two names for exactly the same kind of current
  2. BA rip tide is a large wave that breaks far from shore
  3. CA rip tide is a current that happens only in lakes
  4. DA rip tide is swift tidal flow through inlets and harbor mouths
Why

The terms are often confused; a rip tide is a tidal current in a narrow opening.

S6008

Can dangerous rip currents form in good beach weather?

  1. AYes; rip currents often form on calm, sunny days
  2. BNo; they form only during storms and high winds
  3. CNo; they form only at night when the tide is low
  4. DOnly when the water is very cold and rough
Why

Good weather does not mean safe water; check the local beach forecast.

S6009

Why can published current tables not be relied on to show rip currents?

  1. ARip currents never change their place or strength
  2. BRip currents vary from day to day in force and location
  3. CRip currents only happen during slack tide
  4. DRip currents are too weak for anyone to measure
Why

Rip currents depend on weather, tide and bottom slope.

32 more questions in this group are in the full course.

Unlock the Full Question Bank

Start a 2-day free trial to study every question and take full practice tests. Then $10/month for this course. Cancel anytime in your account. One free trial per person.

End of the free questions

You Have Read All 47 Free Questions

The other 175 are in the full course, with Study mode and the full practice test on every one of them. Month to month: cancel any time, and you keep access until the end of the month you paid for.